|
Re: Oil-filter removal (2004 Jeep Liberty)
gcotterl@co.riverside.ca.us wrote: > The last time I replaced the oil filter, I left the oil-filter cap on > the fluted end of the filter. Now, the oil-filter cap just spins on the > filter. I've gotten the cap off but the fluted "corners" of the filter > have been rounded off so I don't think I can use a new cap. How can I > unscrew the filter? Is there another tool that I can use to grab onto > the filter? I'm not sure how it could ever be that tight. I always do my own oil changes. I put a drop of oil on the filter rubber gasket and tighten it as snug as possible with one hand. I rarely need to use 2 hands to remove it. I have a good selection of filter wrenches because every vehicle I buy seems to require one for the first oil change. My favourites are the fluted cup (fits my 1/2 inch drive bar) and the floppy closed pliers. I haven't used the GBF screwdriver in many years. Merrill |
Re: Oil-filter removal (2004 Jeep Liberty)
The first time I tried to change the oil-filter on my new Jeep Liberty,
I couldn't get the oil-filter off so, after struggling with it for hours (it seemed), I ended up taking it to a lube place. (I suspect that the oil-filter was installed dry at the factory). I did the next oil-filter change. I oiled the rubber gasket and screwed the filter until it was snug then turned it another 1/8 to 1/4 turn. That was only about 3,000 miles ago and 9 months ago -- I only put less than 6,000 miles on my Liberty in a year -- so I don't know why it's so darn hard now. P.S. What are "floppy closed pliers". Can you find a picture of one and send me the URL? Thx, Gary |
Re: Oil-filter removal (2004 Jeep Liberty)
The first time I tried to change the oil-filter on my new Jeep Liberty,
I couldn't get the oil-filter off so, after struggling with it for hours (it seemed), I ended up taking it to a lube place. (I suspect that the oil-filter was installed dry at the factory). I did the next oil-filter change. I oiled the rubber gasket and screwed the filter until it was snug then turned it another 1/8 to 1/4 turn. That was only about 3,000 miles ago and 9 months ago -- I only put less than 6,000 miles on my Liberty in a year -- so I don't know why it's so darn hard now. P.S. What are "floppy closed pliers". Can you find a picture of one and send me the URL? Thx, Gary |
Re: Oil-filter removal (2004 Jeep Liberty)
The first time I tried to change the oil-filter on my new Jeep Liberty,
I couldn't get the oil-filter off so, after struggling with it for hours (it seemed), I ended up taking it to a lube place. (I suspect that the oil-filter was installed dry at the factory). I did the next oil-filter change. I oiled the rubber gasket and screwed the filter until it was snug then turned it another 1/8 to 1/4 turn. That was only about 3,000 miles ago and 9 months ago -- I only put less than 6,000 miles on my Liberty in a year -- so I don't know why it's so darn hard now. P.S. What are "floppy closed pliers". Can you find a picture of one and send me the URL? Thx, Gary |
Re: Oil-filter removal (2004 Jeep Liberty)
The first time I tried to change the oil-filter on my new Jeep Liberty,
I couldn't get the oil-filter off so, after struggling with it for hours (it seemed), I ended up taking it to a lube place. (I suspect that the oil-filter was installed dry at the factory). I did the next oil-filter change. I oiled the rubber gasket and screwed the filter until it was snug then turned it another 1/8 to 1/4 turn. That was only about 3,000 miles ago and 9 months ago -- I only put less than 6,000 miles on my Liberty in a year -- so I don't know why it's so darn hard now. P.S. What are "floppy closed pliers". Can you find a picture of one and send me the URL? Thx, Gary |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok... what is an 'oil filter cap' and why would you leave it on a
filter? Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The last time I replaced the oil filter, I left the oil-filter cap on > the fluted end of the filter. Now, the oil-filter cap just spins on the > filter. I've gotten the cap off but the fluted "corners" of the filter > have been rounded off so I don't think I can use a new cap. How can I > unscrew the filter? Is there another tool that I can use to grab onto > the filter? |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok... what is an 'oil filter cap' and why would you leave it on a
filter? Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The last time I replaced the oil filter, I left the oil-filter cap on > the fluted end of the filter. Now, the oil-filter cap just spins on the > filter. I've gotten the cap off but the fluted "corners" of the filter > have been rounded off so I don't think I can use a new cap. How can I > unscrew the filter? Is there another tool that I can use to grab onto > the filter? |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok... what is an 'oil filter cap' and why would you leave it on a
filter? Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The last time I replaced the oil filter, I left the oil-filter cap on > the fluted end of the filter. Now, the oil-filter cap just spins on the > filter. I've gotten the cap off but the fluted "corners" of the filter > have been rounded off so I don't think I can use a new cap. How can I > unscrew the filter? Is there another tool that I can use to grab onto > the filter? |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok... what is an 'oil filter cap' and why would you leave it on a
filter? Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The last time I replaced the oil filter, I left the oil-filter cap on > the fluted end of the filter. Now, the oil-filter cap just spins on the > filter. I've gotten the cap off but the fluted "corners" of the filter > have been rounded off so I don't think I can use a new cap. How can I > unscrew the filter? Is there another tool that I can use to grab onto > the filter? |
Re: Oil-filter removal (2004 Jeep Liberty)
An oil-filter cap (or cup) fits snuggly over the fluted-end of the
oil-filter. For a pic, see: http://www.toolweb.com/euitemlist.cf...subcatID=44344 The cap has a square hole so a 3/8" socket extension-bar can be used to remove and install the filter. I left the cap on the filter because I knew I'd need it for the next oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
An oil-filter cap (or cup) fits snuggly over the fluted-end of the
oil-filter. For a pic, see: http://www.toolweb.com/euitemlist.cf...subcatID=44344 The cap has a square hole so a 3/8" socket extension-bar can be used to remove and install the filter. I left the cap on the filter because I knew I'd need it for the next oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
An oil-filter cap (or cup) fits snuggly over the fluted-end of the
oil-filter. For a pic, see: http://www.toolweb.com/euitemlist.cf...subcatID=44344 The cap has a square hole so a 3/8" socket extension-bar can be used to remove and install the filter. I left the cap on the filter because I knew I'd need it for the next oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
An oil-filter cap (or cup) fits snuggly over the fluted-end of the
oil-filter. For a pic, see: http://www.toolweb.com/euitemlist.cf...subcatID=44344 The cap has a square hole so a 3/8" socket extension-bar can be used to remove and install the filter. I left the cap on the filter because I knew I'd need it for the next oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok, so you left the removal tool in place and it destroyed the oil
filter if I am reading this right? You are extremely lucky it didn't wear through allowing all your oil to puke out. I have seen too many dead engines from things like that. Even happened to me, by the time the oil light came on from a head that came loose opening an oil passage on a flat 4 during a highway trip, the engine was fried. (the $tealership actually screwed that one up) I think the tool is now likely damaged as well so I think I would just glue the sucker back onto the filter and remove it that way. JB weld or some other epoxy comes to mind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > An oil-filter cap (or cup) fits snuggly over the fluted-end of the > oil-filter. For a pic, see: > > http://www.toolweb.com/euitemlist.cf...subcatID=44344 > > The cap has a square hole so a 3/8" socket extension-bar can be used to > remove and install the filter. > > I left the cap on the filter because I knew I'd need it for the next > oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok, so you left the removal tool in place and it destroyed the oil
filter if I am reading this right? You are extremely lucky it didn't wear through allowing all your oil to puke out. I have seen too many dead engines from things like that. Even happened to me, by the time the oil light came on from a head that came loose opening an oil passage on a flat 4 during a highway trip, the engine was fried. (the $tealership actually screwed that one up) I think the tool is now likely damaged as well so I think I would just glue the sucker back onto the filter and remove it that way. JB weld or some other epoxy comes to mind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > An oil-filter cap (or cup) fits snuggly over the fluted-end of the > oil-filter. For a pic, see: > > http://www.toolweb.com/euitemlist.cf...subcatID=44344 > > The cap has a square hole so a 3/8" socket extension-bar can be used to > remove and install the filter. > > I left the cap on the filter because I knew I'd need it for the next > oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok, so you left the removal tool in place and it destroyed the oil
filter if I am reading this right? You are extremely lucky it didn't wear through allowing all your oil to puke out. I have seen too many dead engines from things like that. Even happened to me, by the time the oil light came on from a head that came loose opening an oil passage on a flat 4 during a highway trip, the engine was fried. (the $tealership actually screwed that one up) I think the tool is now likely damaged as well so I think I would just glue the sucker back onto the filter and remove it that way. JB weld or some other epoxy comes to mind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > An oil-filter cap (or cup) fits snuggly over the fluted-end of the > oil-filter. For a pic, see: > > http://www.toolweb.com/euitemlist.cf...subcatID=44344 > > The cap has a square hole so a 3/8" socket extension-bar can be used to > remove and install the filter. > > I left the cap on the filter because I knew I'd need it for the next > oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
Ok, so you left the removal tool in place and it destroyed the oil
filter if I am reading this right? You are extremely lucky it didn't wear through allowing all your oil to puke out. I have seen too many dead engines from things like that. Even happened to me, by the time the oil light came on from a head that came loose opening an oil passage on a flat 4 during a highway trip, the engine was fried. (the $tealership actually screwed that one up) I think the tool is now likely damaged as well so I think I would just glue the sucker back onto the filter and remove it that way. JB weld or some other epoxy comes to mind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > An oil-filter cap (or cup) fits snuggly over the fluted-end of the > oil-filter. For a pic, see: > > http://www.toolweb.com/euitemlist.cf...subcatID=44344 > > The cap has a square hole so a 3/8" socket extension-bar can be used to > remove and install the filter. > > I left the cap on the filter because I knew I'd need it for the next > oil-filter change and I didn't want to go hunting for it in my garage. |
Re: Oil-filter removal (2004 Jeep Liberty)
The removal tool did NOT destroy the oil filter; it just rounded-off
the flutes on the filter. Now, I need to find something that will grab onto the filter so it can be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
The removal tool did NOT destroy the oil filter; it just rounded-off
the flutes on the filter. Now, I need to find something that will grab onto the filter so it can be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
The removal tool did NOT destroy the oil filter; it just rounded-off
the flutes on the filter. Now, I need to find something that will grab onto the filter so it can be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
The removal tool did NOT destroy the oil filter; it just rounded-off
the flutes on the filter. Now, I need to find something that will grab onto the filter so it can be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Do you realize how thin the oil filter metal is? Mine rubbed on the
engine mount once and blew/wore a hole through it very fast. It wore out the crease on a flute. Rounding the flutes wore on the flute crease marks also. I still figure you were lucky.... So what about just gluing the tool back onto the filter???? Like I said, the tool is also likely worn so it wouldn't be good to use again anyway. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The removal tool did NOT destroy the oil filter; it just rounded-off > the flutes on the filter. > > Now, I need to find something that will grab onto the filter so it can > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Do you realize how thin the oil filter metal is? Mine rubbed on the
engine mount once and blew/wore a hole through it very fast. It wore out the crease on a flute. Rounding the flutes wore on the flute crease marks also. I still figure you were lucky.... So what about just gluing the tool back onto the filter???? Like I said, the tool is also likely worn so it wouldn't be good to use again anyway. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The removal tool did NOT destroy the oil filter; it just rounded-off > the flutes on the filter. > > Now, I need to find something that will grab onto the filter so it can > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Do you realize how thin the oil filter metal is? Mine rubbed on the
engine mount once and blew/wore a hole through it very fast. It wore out the crease on a flute. Rounding the flutes wore on the flute crease marks also. I still figure you were lucky.... So what about just gluing the tool back onto the filter???? Like I said, the tool is also likely worn so it wouldn't be good to use again anyway. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The removal tool did NOT destroy the oil filter; it just rounded-off > the flutes on the filter. > > Now, I need to find something that will grab onto the filter so it can > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Do you realize how thin the oil filter metal is? Mine rubbed on the
engine mount once and blew/wore a hole through it very fast. It wore out the crease on a flute. Rounding the flutes wore on the flute crease marks also. I still figure you were lucky.... So what about just gluing the tool back onto the filter???? Like I said, the tool is also likely worn so it wouldn't be good to use again anyway. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) gcotterl@co.riverside.ca.us wrote: > > The removal tool did NOT destroy the oil filter; it just rounded-off > the flutes on the filter. > > Now, I need to find something that will grab onto the filter so it can > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Mike,
What he is not saying here, is whether he used the "oil filter removal tool" to install the filter, that now won't come off. I am betting that he did. Spin-on oil filters are designed to be installed by hand. I don't care how tight this filter is. None of them will resist big channel-locking pliers or a pipe wrench for long. Earle "Mike Romain" <romainm@sympatico.ca> wrote in message news:44F309D1.B1EEC060@sympatico.ca... > Do you realize how thin the oil filter metal is? Mine rubbed on the > engine mount once and blew/wore a hole through it very fast. It wore out > the crease on a flute. Rounding the flutes wore on the flute crease > marks also. I still figure you were lucky.... > > So what about just gluing the tool back onto the filter???? Like I > said, the tool is also likely worn so it wouldn't be good to use again > anyway. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) > > gcotterl@co.riverside.ca.us wrote: > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > the flutes on the filter. > > > > Now, I need to find something that will grab onto the filter so it can > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Mike,
What he is not saying here, is whether he used the "oil filter removal tool" to install the filter, that now won't come off. I am betting that he did. Spin-on oil filters are designed to be installed by hand. I don't care how tight this filter is. None of them will resist big channel-locking pliers or a pipe wrench for long. Earle "Mike Romain" <romainm@sympatico.ca> wrote in message news:44F309D1.B1EEC060@sympatico.ca... > Do you realize how thin the oil filter metal is? Mine rubbed on the > engine mount once and blew/wore a hole through it very fast. It wore out > the crease on a flute. Rounding the flutes wore on the flute crease > marks also. I still figure you were lucky.... > > So what about just gluing the tool back onto the filter???? Like I > said, the tool is also likely worn so it wouldn't be good to use again > anyway. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) > > gcotterl@co.riverside.ca.us wrote: > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > the flutes on the filter. > > > > Now, I need to find something that will grab onto the filter so it can > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Mike,
What he is not saying here, is whether he used the "oil filter removal tool" to install the filter, that now won't come off. I am betting that he did. Spin-on oil filters are designed to be installed by hand. I don't care how tight this filter is. None of them will resist big channel-locking pliers or a pipe wrench for long. Earle "Mike Romain" <romainm@sympatico.ca> wrote in message news:44F309D1.B1EEC060@sympatico.ca... > Do you realize how thin the oil filter metal is? Mine rubbed on the > engine mount once and blew/wore a hole through it very fast. It wore out > the crease on a flute. Rounding the flutes wore on the flute crease > marks also. I still figure you were lucky.... > > So what about just gluing the tool back onto the filter???? Like I > said, the tool is also likely worn so it wouldn't be good to use again > anyway. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) > > gcotterl@co.riverside.ca.us wrote: > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > the flutes on the filter. > > > > Now, I need to find something that will grab onto the filter so it can > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
Mike,
What he is not saying here, is whether he used the "oil filter removal tool" to install the filter, that now won't come off. I am betting that he did. Spin-on oil filters are designed to be installed by hand. I don't care how tight this filter is. None of them will resist big channel-locking pliers or a pipe wrench for long. Earle "Mike Romain" <romainm@sympatico.ca> wrote in message news:44F309D1.B1EEC060@sympatico.ca... > Do you realize how thin the oil filter metal is? Mine rubbed on the > engine mount once and blew/wore a hole through it very fast. It wore out > the crease on a flute. Rounding the flutes wore on the flute crease > marks also. I still figure you were lucky.... > > So what about just gluing the tool back onto the filter???? Like I > said, the tool is also likely worn so it wouldn't be good to use again > anyway. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) > > gcotterl@co.riverside.ca.us wrote: > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > the flutes on the filter. > > > > Now, I need to find something that will grab onto the filter so it can > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
I caught that to Earle. He actually 'does' say he used it to put the
filter on in one post. I'll be he just uses his hand next time.... Mike Earle Horton wrote: > > Mike, > > What he is not saying here, is whether he used the "oil filter removal tool" > to install the filter, that now won't come off. I am betting that he did. > Spin-on oil filters are designed to be installed by hand. > > I don't care how tight this filter is. None of them will resist big > channel-locking pliers or a pipe wrench for long. > > Earle > > "Mike Romain" <romainm@sympatico.ca> wrote in message > news:44F309D1.B1EEC060@sympatico.ca... > > Do you realize how thin the oil filter metal is? Mine rubbed on the > > engine mount once and blew/wore a hole through it very fast. It wore out > > the crease on a flute. Rounding the flutes wore on the flute crease > > marks also. I still figure you were lucky.... > > > > So what about just gluing the tool back onto the filter???? Like I > > said, the tool is also likely worn so it wouldn't be good to use again > > anyway. > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > > > > gcotterl@co.riverside.ca.us wrote: > > > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > > the flutes on the filter. > > > > > > Now, I need to find something that will grab onto the filter so it can > > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
I caught that to Earle. He actually 'does' say he used it to put the
filter on in one post. I'll be he just uses his hand next time.... Mike Earle Horton wrote: > > Mike, > > What he is not saying here, is whether he used the "oil filter removal tool" > to install the filter, that now won't come off. I am betting that he did. > Spin-on oil filters are designed to be installed by hand. > > I don't care how tight this filter is. None of them will resist big > channel-locking pliers or a pipe wrench for long. > > Earle > > "Mike Romain" <romainm@sympatico.ca> wrote in message > news:44F309D1.B1EEC060@sympatico.ca... > > Do you realize how thin the oil filter metal is? Mine rubbed on the > > engine mount once and blew/wore a hole through it very fast. It wore out > > the crease on a flute. Rounding the flutes wore on the flute crease > > marks also. I still figure you were lucky.... > > > > So what about just gluing the tool back onto the filter???? Like I > > said, the tool is also likely worn so it wouldn't be good to use again > > anyway. > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > > > > gcotterl@co.riverside.ca.us wrote: > > > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > > the flutes on the filter. > > > > > > Now, I need to find something that will grab onto the filter so it can > > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
I caught that to Earle. He actually 'does' say he used it to put the
filter on in one post. I'll be he just uses his hand next time.... Mike Earle Horton wrote: > > Mike, > > What he is not saying here, is whether he used the "oil filter removal tool" > to install the filter, that now won't come off. I am betting that he did. > Spin-on oil filters are designed to be installed by hand. > > I don't care how tight this filter is. None of them will resist big > channel-locking pliers or a pipe wrench for long. > > Earle > > "Mike Romain" <romainm@sympatico.ca> wrote in message > news:44F309D1.B1EEC060@sympatico.ca... > > Do you realize how thin the oil filter metal is? Mine rubbed on the > > engine mount once and blew/wore a hole through it very fast. It wore out > > the crease on a flute. Rounding the flutes wore on the flute crease > > marks also. I still figure you were lucky.... > > > > So what about just gluing the tool back onto the filter???? Like I > > said, the tool is also likely worn so it wouldn't be good to use again > > anyway. > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > > > > gcotterl@co.riverside.ca.us wrote: > > > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > > the flutes on the filter. > > > > > > Now, I need to find something that will grab onto the filter so it can > > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
I caught that to Earle. He actually 'does' say he used it to put the
filter on in one post. I'll be he just uses his hand next time.... Mike Earle Horton wrote: > > Mike, > > What he is not saying here, is whether he used the "oil filter removal tool" > to install the filter, that now won't come off. I am betting that he did. > Spin-on oil filters are designed to be installed by hand. > > I don't care how tight this filter is. None of them will resist big > channel-locking pliers or a pipe wrench for long. > > Earle > > "Mike Romain" <romainm@sympatico.ca> wrote in message > news:44F309D1.B1EEC060@sympatico.ca... > > Do you realize how thin the oil filter metal is? Mine rubbed on the > > engine mount once and blew/wore a hole through it very fast. It wore out > > the crease on a flute. Rounding the flutes wore on the flute crease > > marks also. I still figure you were lucky.... > > > > So what about just gluing the tool back onto the filter???? Like I > > said, the tool is also likely worn so it wouldn't be good to use again > > anyway. > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > > > > gcotterl@co.riverside.ca.us wrote: > > > > > > The removal tool did NOT destroy the oil filter; it just rounded-off > > > the flutes on the filter. > > > > > > Now, I need to find something that will grab onto the filter so it can > > > be unscrewed. |
Re: Oil-filter removal (2004 Jeep Liberty)
I had to use the "removal" tool to install the oil filter because it's
hard to squeeze one's arm between the fan-shroud and the tie-rod, reach the oil filter and screw it on -- there's just not enough room to work in. Anyway, I turned the "removal" tool just enough to result in an "hand-tight" fit. |
Re: Oil-filter removal (2004 Jeep Liberty)
I had to use the "removal" tool to install the oil filter because it's
hard to squeeze one's arm between the fan-shroud and the tie-rod, reach the oil filter and screw it on -- there's just not enough room to work in. Anyway, I turned the "removal" tool just enough to result in an "hand-tight" fit. |
Re: Oil-filter removal (2004 Jeep Liberty)
I had to use the "removal" tool to install the oil filter because it's
hard to squeeze one's arm between the fan-shroud and the tie-rod, reach the oil filter and screw it on -- there's just not enough room to work in. Anyway, I turned the "removal" tool just enough to result in an "hand-tight" fit. |
Re: Oil-filter removal (2004 Jeep Liberty)
I had to use the "removal" tool to install the oil filter because it's
hard to squeeze one's arm between the fan-shroud and the tie-rod, reach the oil filter and screw it on -- there's just not enough room to work in. Anyway, I turned the "removal" tool just enough to result in an "hand-tight" fit. |
Re: Oil-filter removal (2004 Jeep Liberty)
<gcotterl@co.riverside.ca.us> wrote in message
news:1156785295.308400.305250@p79g2000cwp.googlegr oups.com... > I had to use the "removal" tool to install the oil filter because > it's hard to squeeze one's arm between the fan-shroud and > the tie-rod, reach the oil filter and screw it on -- there's just > not enough room to work in. Anyway, I turned the "removal" > tool just enough to result in an "hand-tight" fit. > They all say that. ;^) Cheers. Earle |
Re: Oil-filter removal (2004 Jeep Liberty)
<gcotterl@co.riverside.ca.us> wrote in message
news:1156785295.308400.305250@p79g2000cwp.googlegr oups.com... > I had to use the "removal" tool to install the oil filter because > it's hard to squeeze one's arm between the fan-shroud and > the tie-rod, reach the oil filter and screw it on -- there's just > not enough room to work in. Anyway, I turned the "removal" > tool just enough to result in an "hand-tight" fit. > They all say that. ;^) Cheers. Earle |
Re: Oil-filter removal (2004 Jeep Liberty)
<gcotterl@co.riverside.ca.us> wrote in message
news:1156785295.308400.305250@p79g2000cwp.googlegr oups.com... > I had to use the "removal" tool to install the oil filter because > it's hard to squeeze one's arm between the fan-shroud and > the tie-rod, reach the oil filter and screw it on -- there's just > not enough room to work in. Anyway, I turned the "removal" > tool just enough to result in an "hand-tight" fit. > They all say that. ;^) Cheers. Earle |
| All times are GMT -4. The time now is 09:22 PM. |
© 2024 MH Sub I, LLC dba Internet Brands