Carter BBD - End of story for now
08-30-2004 | 09:34 PM
#1
Guest
Posts: n/a
Carter BBD - End of story for now
Following several suggestions, I got the Jeep running better than it has in
years. Computer not working, but I cleaned the idle tubes, aedjusted the
mixture, and enjoyed my ride again. After 110 miles, it started running
rotten again.
My best guess is that the computer kicked in for a few seconds, and adjusted
the mixture to full lean.
I decided I need to get the computer running. I installed 2 fuses in the
circuit board next to the battery, and checked the O2 sensor, water jacker
thermocouple, and the other thingy in the air filter. Within a few minutes,
I had the computer working, and adjusting the mixture.
Life is good.
Until.......
It stopped working again, and I let the smoke out of the wires inside the
harness.
Jeep won't run.
2 Options:
Find a new harness (I haven't seen one for a YJ)
Replace ignition and carb with wired kits.
years. Computer not working, but I cleaned the idle tubes, aedjusted the
mixture, and enjoyed my ride again. After 110 miles, it started running
rotten again.
My best guess is that the computer kicked in for a few seconds, and adjusted
the mixture to full lean.
I decided I need to get the computer running. I installed 2 fuses in the
circuit board next to the battery, and checked the O2 sensor, water jacker
thermocouple, and the other thingy in the air filter. Within a few minutes,
I had the computer working, and adjusting the mixture.
Life is good.
Until.......
It stopped working again, and I let the smoke out of the wires inside the
harness.
Jeep won't run.
2 Options:
Find a new harness (I haven't seen one for a YJ)
Replace ignition and carb with wired kits.
08-30-2004 | 10:28 PM
#2
Guest
Posts: n/a
Re: Carter BBD - End of story for now
I was just wondering if you can hear the Nutter people telling you
"I told ya so"!
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve Foley wrote:
>
> Following several suggestions, I got the Jeep running better than it has in
> years. Computer not working, but I cleaned the idle tubes, aedjusted the
> mixture, and enjoyed my ride again. After 110 miles, it started running
> rotten again.
>
> My best guess is that the computer kicked in for a few seconds, and adjusted
> the mixture to full lean.
>
> I decided I need to get the computer running. I installed 2 fuses in the
> circuit board next to the battery, and checked the O2 sensor, water jacker
> thermocouple, and the other thingy in the air filter. Within a few minutes,
> I had the computer working, and adjusting the mixture.
>
> Life is good.
>
> Until.......
>
> It stopped working again, and I let the smoke out of the wires inside the
> harness.
>
> Jeep won't run.
>
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
>
> Replace ignition and carb with wired kits.
"I told ya so"!
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve Foley wrote:
>
> Following several suggestions, I got the Jeep running better than it has in
> years. Computer not working, but I cleaned the idle tubes, aedjusted the
> mixture, and enjoyed my ride again. After 110 miles, it started running
> rotten again.
>
> My best guess is that the computer kicked in for a few seconds, and adjusted
> the mixture to full lean.
>
> I decided I need to get the computer running. I installed 2 fuses in the
> circuit board next to the battery, and checked the O2 sensor, water jacker
> thermocouple, and the other thingy in the air filter. Within a few minutes,
> I had the computer working, and adjusting the mixture.
>
> Life is good.
>
> Until.......
>
> It stopped working again, and I let the smoke out of the wires inside the
> harness.
>
> Jeep won't run.
>
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
>
> Replace ignition and carb with wired kits.
08-30-2004 | 10:28 PM
#3
Guest
Posts: n/a
Re: Carter BBD - End of story for now
I was just wondering if you can hear the Nutter people telling you
"I told ya so"!
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve Foley wrote:
>
> Following several suggestions, I got the Jeep running better than it has in
> years. Computer not working, but I cleaned the idle tubes, aedjusted the
> mixture, and enjoyed my ride again. After 110 miles, it started running
> rotten again.
>
> My best guess is that the computer kicked in for a few seconds, and adjusted
> the mixture to full lean.
>
> I decided I need to get the computer running. I installed 2 fuses in the
> circuit board next to the battery, and checked the O2 sensor, water jacker
> thermocouple, and the other thingy in the air filter. Within a few minutes,
> I had the computer working, and adjusting the mixture.
>
> Life is good.
>
> Until.......
>
> It stopped working again, and I let the smoke out of the wires inside the
> harness.
>
> Jeep won't run.
>
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
>
> Replace ignition and carb with wired kits.
"I told ya so"!
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve Foley wrote:
>
> Following several suggestions, I got the Jeep running better than it has in
> years. Computer not working, but I cleaned the idle tubes, aedjusted the
> mixture, and enjoyed my ride again. After 110 miles, it started running
> rotten again.
>
> My best guess is that the computer kicked in for a few seconds, and adjusted
> the mixture to full lean.
>
> I decided I need to get the computer running. I installed 2 fuses in the
> circuit board next to the battery, and checked the O2 sensor, water jacker
> thermocouple, and the other thingy in the air filter. Within a few minutes,
> I had the computer working, and adjusting the mixture.
>
> Life is good.
>
> Until.......
>
> It stopped working again, and I let the smoke out of the wires inside the
> harness.
>
> Jeep won't run.
>
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
>
> Replace ignition and carb with wired kits.
08-30-2004 | 10:28 PM
#4
Guest
Posts: n/a
Re: Carter BBD - End of story for now
I was just wondering if you can hear the Nutter people telling you
"I told ya so"!
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve Foley wrote:
>
> Following several suggestions, I got the Jeep running better than it has in
> years. Computer not working, but I cleaned the idle tubes, aedjusted the
> mixture, and enjoyed my ride again. After 110 miles, it started running
> rotten again.
>
> My best guess is that the computer kicked in for a few seconds, and adjusted
> the mixture to full lean.
>
> I decided I need to get the computer running. I installed 2 fuses in the
> circuit board next to the battery, and checked the O2 sensor, water jacker
> thermocouple, and the other thingy in the air filter. Within a few minutes,
> I had the computer working, and adjusting the mixture.
>
> Life is good.
>
> Until.......
>
> It stopped working again, and I let the smoke out of the wires inside the
> harness.
>
> Jeep won't run.
>
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
>
> Replace ignition and carb with wired kits.
"I told ya so"!
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve Foley wrote:
>
> Following several suggestions, I got the Jeep running better than it has in
> years. Computer not working, but I cleaned the idle tubes, aedjusted the
> mixture, and enjoyed my ride again. After 110 miles, it started running
> rotten again.
>
> My best guess is that the computer kicked in for a few seconds, and adjusted
> the mixture to full lean.
>
> I decided I need to get the computer running. I installed 2 fuses in the
> circuit board next to the battery, and checked the O2 sensor, water jacker
> thermocouple, and the other thingy in the air filter. Within a few minutes,
> I had the computer working, and adjusting the mixture.
>
> Life is good.
>
> Until.......
>
> It stopped working again, and I let the smoke out of the wires inside the
> harness.
>
> Jeep won't run.
>
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
>
> Replace ignition and carb with wired kits.
08-30-2004 | 10:40 PM
#5
Guest
Posts: n/a
Re: Carter BBD - End of story for now
Steve Foley did pass the time by typing:
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
Painless might have one.
> Replace ignition and carb with wired kits.
Well, you probably know now that fuses have ratings and putting in a larger
fuse means something else will burn out. :(
Since things are dead you might try the "nutter bypass".
http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
The other option is a fuel injector conversion. $$$ but what I've read
indicates happy campers.
.../me wonders if they make a TBI system which would be easier to install. :/
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
Painless might have one.
> Replace ignition and carb with wired kits.
Well, you probably know now that fuses have ratings and putting in a larger
fuse means something else will burn out. :(
Since things are dead you might try the "nutter bypass".
http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
The other option is a fuel injector conversion. $$$ but what I've read
indicates happy campers.
.../me wonders if they make a TBI system which would be easier to install. :/
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
08-30-2004 | 10:40 PM
#6
Guest
Posts: n/a
Re: Carter BBD - End of story for now
Steve Foley did pass the time by typing:
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
Painless might have one.
> Replace ignition and carb with wired kits.
Well, you probably know now that fuses have ratings and putting in a larger
fuse means something else will burn out. :(
Since things are dead you might try the "nutter bypass".
http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
The other option is a fuel injector conversion. $$$ but what I've read
indicates happy campers.
.../me wonders if they make a TBI system which would be easier to install. :/
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
Painless might have one.
> Replace ignition and carb with wired kits.
Well, you probably know now that fuses have ratings and putting in a larger
fuse means something else will burn out. :(
Since things are dead you might try the "nutter bypass".
http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
The other option is a fuel injector conversion. $$$ but what I've read
indicates happy campers.
.../me wonders if they make a TBI system which would be easier to install. :/
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
08-30-2004 | 10:40 PM
#7
Guest
Posts: n/a
Re: Carter BBD - End of story for now
Steve Foley did pass the time by typing:
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
Painless might have one.
> Replace ignition and carb with wired kits.
Well, you probably know now that fuses have ratings and putting in a larger
fuse means something else will burn out. :(
Since things are dead you might try the "nutter bypass".
http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
The other option is a fuel injector conversion. $$$ but what I've read
indicates happy campers.
.../me wonders if they make a TBI system which would be easier to install. :/
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> 2 Options:
>
> Find a new harness (I haven't seen one for a YJ)
Painless might have one.
> Replace ignition and carb with wired kits.
Well, you probably know now that fuses have ratings and putting in a larger
fuse means something else will burn out. :(
Since things are dead you might try the "nutter bypass".
http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
The other option is a fuel injector conversion. $$$ but what I've read
indicates happy campers.
.../me wonders if they make a TBI system which would be easier to install. :/
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
08-30-2004 | 11:09 PM
#8
Guest
Posts: n/a
Re: Carter BBD - End of story for now
I was told they were 1 amp fuses. I replaced them with 1 amp fuses.
From the other thread, ten years ago, choke wire melted to exhaust manifold,
and caused 22 wires to become 1 (including engaging the starter while I was
doing 70). My best guess is that the computer's been dead for ten years.
I'll try the nutter bypass and unplug the carb.
Anyone know how I can move the electric mixture pins? 12 volts to ???
"DougW" <post.replies@invalid.address> wrote in message
news:2GQYc.71013$wo.51006@okepread06...
> Steve Foley did pass the time by typing:
>
> > 2 Options:
> >
> > Find a new harness (I haven't seen one for a YJ)
>
> Painless might have one.
>
> > Replace ignition and carb with wired kits.
>
> Well, you probably know now that fuses have ratings and putting in a
larger
> fuse means something else will burn out. :(
>
> Since things are dead you might try the "nutter bypass".
> http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
>
> The other option is a fuel injector conversion. $$$ but what I've read
> indicates happy campers.
>
> ../me wonders if they make a TBI system which would be easier to install.
:/
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
From the other thread, ten years ago, choke wire melted to exhaust manifold,
and caused 22 wires to become 1 (including engaging the starter while I was
doing 70). My best guess is that the computer's been dead for ten years.
I'll try the nutter bypass and unplug the carb.
Anyone know how I can move the electric mixture pins? 12 volts to ???
"DougW" <post.replies@invalid.address> wrote in message
news:2GQYc.71013$wo.51006@okepread06...
> Steve Foley did pass the time by typing:
>
> > 2 Options:
> >
> > Find a new harness (I haven't seen one for a YJ)
>
> Painless might have one.
>
> > Replace ignition and carb with wired kits.
>
> Well, you probably know now that fuses have ratings and putting in a
larger
> fuse means something else will burn out. :(
>
> Since things are dead you might try the "nutter bypass".
> http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
>
> The other option is a fuel injector conversion. $$$ but what I've read
> indicates happy campers.
>
> ../me wonders if they make a TBI system which would be easier to install.
:/
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
08-30-2004 | 11:09 PM
#9
Guest
Posts: n/a
Re: Carter BBD - End of story for now
I was told they were 1 amp fuses. I replaced them with 1 amp fuses.
From the other thread, ten years ago, choke wire melted to exhaust manifold,
and caused 22 wires to become 1 (including engaging the starter while I was
doing 70). My best guess is that the computer's been dead for ten years.
I'll try the nutter bypass and unplug the carb.
Anyone know how I can move the electric mixture pins? 12 volts to ???
"DougW" <post.replies@invalid.address> wrote in message
news:2GQYc.71013$wo.51006@okepread06...
> Steve Foley did pass the time by typing:
>
> > 2 Options:
> >
> > Find a new harness (I haven't seen one for a YJ)
>
> Painless might have one.
>
> > Replace ignition and carb with wired kits.
>
> Well, you probably know now that fuses have ratings and putting in a
larger
> fuse means something else will burn out. :(
>
> Since things are dead you might try the "nutter bypass".
> http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
>
> The other option is a fuel injector conversion. $$$ but what I've read
> indicates happy campers.
>
> ../me wonders if they make a TBI system which would be easier to install.
:/
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
From the other thread, ten years ago, choke wire melted to exhaust manifold,
and caused 22 wires to become 1 (including engaging the starter while I was
doing 70). My best guess is that the computer's been dead for ten years.
I'll try the nutter bypass and unplug the carb.
Anyone know how I can move the electric mixture pins? 12 volts to ???
"DougW" <post.replies@invalid.address> wrote in message
news:2GQYc.71013$wo.51006@okepread06...
> Steve Foley did pass the time by typing:
>
> > 2 Options:
> >
> > Find a new harness (I haven't seen one for a YJ)
>
> Painless might have one.
>
> > Replace ignition and carb with wired kits.
>
> Well, you probably know now that fuses have ratings and putting in a
larger
> fuse means something else will burn out. :(
>
> Since things are dead you might try the "nutter bypass".
> http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
>
> The other option is a fuel injector conversion. $$$ but what I've read
> indicates happy campers.
>
> ../me wonders if they make a TBI system which would be easier to install.
:/
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
08-30-2004 | 11:09 PM
#10
Guest
Posts: n/a
Re: Carter BBD - End of story for now
I was told they were 1 amp fuses. I replaced them with 1 amp fuses.
From the other thread, ten years ago, choke wire melted to exhaust manifold,
and caused 22 wires to become 1 (including engaging the starter while I was
doing 70). My best guess is that the computer's been dead for ten years.
I'll try the nutter bypass and unplug the carb.
Anyone know how I can move the electric mixture pins? 12 volts to ???
"DougW" <post.replies@invalid.address> wrote in message
news:2GQYc.71013$wo.51006@okepread06...
> Steve Foley did pass the time by typing:
>
> > 2 Options:
> >
> > Find a new harness (I haven't seen one for a YJ)
>
> Painless might have one.
>
> > Replace ignition and carb with wired kits.
>
> Well, you probably know now that fuses have ratings and putting in a
larger
> fuse means something else will burn out. :(
>
> Since things are dead you might try the "nutter bypass".
> http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
>
> The other option is a fuel injector conversion. $$$ but what I've read
> indicates happy campers.
>
> ../me wonders if they make a TBI system which would be easier to install.
:/
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>
From the other thread, ten years ago, choke wire melted to exhaust manifold,
and caused 22 wires to become 1 (including engaging the starter while I was
doing 70). My best guess is that the computer's been dead for ten years.
I'll try the nutter bypass and unplug the carb.
Anyone know how I can move the electric mixture pins? 12 volts to ???
"DougW" <post.replies@invalid.address> wrote in message
news:2GQYc.71013$wo.51006@okepread06...
> Steve Foley did pass the time by typing:
>
> > 2 Options:
> >
> > Find a new harness (I haven't seen one for a YJ)
>
> Painless might have one.
>
> > Replace ignition and carb with wired kits.
>
> Well, you probably know now that fuses have ratings and putting in a
larger
> fuse means something else will burn out. :(
>
> Since things are dead you might try the "nutter bypass".
> http://www.4x4wire.com/jeep/tech/ele...jn-ignition99/
>
> The other option is a fuel injector conversion. $$$ but what I've read
> indicates happy campers.
>
> ../me wonders if they make a TBI system which would be easier to install.
:/
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
>
>