access instrument cluster connector & speedo sensor troubleshooting
03-28-2005 | 11:20 AM
#11
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Well, stalling in neutral is because you have the speed sensor
disconnected.
If you reconnect it and it stops stalling, the sensor is likely working.
The sensor generates it's own pulses. Just spin it by hand with a meter
on it. 8 pulses per revolution off pin 1 and 2 likely.
'What' is the speedometer doing or not doing anyway?
To pull the codes, you need to hook everything back up and drive it for
a bit.
Then stop, rev it ti 2500 and let it down to idle and cycle everything
like the AC and if an automatic all the gears.
Then shut it down and turn the key on, off, on, off, on and count the
flashes on the dash light. It will flash a sequence, then pause, then
flash again. The final flash will be a 5 and a 5 or code 55 that means
no more codes.
If you get a code 15, the speed sensor or it's circuit is bad.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
updawaz00@hotmail.com wrote:
>
> First off what are you trying to fix?
>
> [ Speedometer in this instance... but also stalling problem in neutral
> After talking to someone you basically have three wires going to sensor
> 5V source input (black), Gnd, and 5V output to Speedometer / Odometer
> gauge. If there is not 5V input then it is probably the wiring or
> gauge, if there is 5V in , probably sensor, but If it is not the
> sensor, I'm not sure how to access cluster connector]
>
> Second, no one here is a mind reader or knows you so we have no clue
> what you are driving. (let alone lots of us do own more than one type
> of Jeep)
> [ YJ, 1992 Wrangler 4.0L ]
>
> And third if it is a YJ you are talking about, why don't you just pull
> the codes and see what the computer 'thinks' is wrong?
> [ No experience with reading code... I't sounds like a great
> troubleshooting tool, do you need a reading device and where do you
> access the port for connection ? Where do I buy one or do I have to
> take it to a shop?]
> Thanks
disconnected.
If you reconnect it and it stops stalling, the sensor is likely working.
The sensor generates it's own pulses. Just spin it by hand with a meter
on it. 8 pulses per revolution off pin 1 and 2 likely.
'What' is the speedometer doing or not doing anyway?
To pull the codes, you need to hook everything back up and drive it for
a bit.
Then stop, rev it ti 2500 and let it down to idle and cycle everything
like the AC and if an automatic all the gears.
Then shut it down and turn the key on, off, on, off, on and count the
flashes on the dash light. It will flash a sequence, then pause, then
flash again. The final flash will be a 5 and a 5 or code 55 that means
no more codes.
If you get a code 15, the speed sensor or it's circuit is bad.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
updawaz00@hotmail.com wrote:
>
> First off what are you trying to fix?
>
> [ Speedometer in this instance... but also stalling problem in neutral
> After talking to someone you basically have three wires going to sensor
> 5V source input (black), Gnd, and 5V output to Speedometer / Odometer
> gauge. If there is not 5V input then it is probably the wiring or
> gauge, if there is 5V in , probably sensor, but If it is not the
> sensor, I'm not sure how to access cluster connector]
>
> Second, no one here is a mind reader or knows you so we have no clue
> what you are driving. (let alone lots of us do own more than one type
> of Jeep)
> [ YJ, 1992 Wrangler 4.0L ]
>
> And third if it is a YJ you are talking about, why don't you just pull
> the codes and see what the computer 'thinks' is wrong?
> [ No experience with reading code... I't sounds like a great
> troubleshooting tool, do you need a reading device and where do you
> access the port for connection ? Where do I buy one or do I have to
> take it to a shop?]
> Thanks
03-28-2005 | 11:20 AM
#12
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Well, stalling in neutral is because you have the speed sensor
disconnected.
If you reconnect it and it stops stalling, the sensor is likely working.
The sensor generates it's own pulses. Just spin it by hand with a meter
on it. 8 pulses per revolution off pin 1 and 2 likely.
'What' is the speedometer doing or not doing anyway?
To pull the codes, you need to hook everything back up and drive it for
a bit.
Then stop, rev it ti 2500 and let it down to idle and cycle everything
like the AC and if an automatic all the gears.
Then shut it down and turn the key on, off, on, off, on and count the
flashes on the dash light. It will flash a sequence, then pause, then
flash again. The final flash will be a 5 and a 5 or code 55 that means
no more codes.
If you get a code 15, the speed sensor or it's circuit is bad.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
updawaz00@hotmail.com wrote:
>
> First off what are you trying to fix?
>
> [ Speedometer in this instance... but also stalling problem in neutral
> After talking to someone you basically have three wires going to sensor
> 5V source input (black), Gnd, and 5V output to Speedometer / Odometer
> gauge. If there is not 5V input then it is probably the wiring or
> gauge, if there is 5V in , probably sensor, but If it is not the
> sensor, I'm not sure how to access cluster connector]
>
> Second, no one here is a mind reader or knows you so we have no clue
> what you are driving. (let alone lots of us do own more than one type
> of Jeep)
> [ YJ, 1992 Wrangler 4.0L ]
>
> And third if it is a YJ you are talking about, why don't you just pull
> the codes and see what the computer 'thinks' is wrong?
> [ No experience with reading code... I't sounds like a great
> troubleshooting tool, do you need a reading device and where do you
> access the port for connection ? Where do I buy one or do I have to
> take it to a shop?]
> Thanks
disconnected.
If you reconnect it and it stops stalling, the sensor is likely working.
The sensor generates it's own pulses. Just spin it by hand with a meter
on it. 8 pulses per revolution off pin 1 and 2 likely.
'What' is the speedometer doing or not doing anyway?
To pull the codes, you need to hook everything back up and drive it for
a bit.
Then stop, rev it ti 2500 and let it down to idle and cycle everything
like the AC and if an automatic all the gears.
Then shut it down and turn the key on, off, on, off, on and count the
flashes on the dash light. It will flash a sequence, then pause, then
flash again. The final flash will be a 5 and a 5 or code 55 that means
no more codes.
If you get a code 15, the speed sensor or it's circuit is bad.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
updawaz00@hotmail.com wrote:
>
> First off what are you trying to fix?
>
> [ Speedometer in this instance... but also stalling problem in neutral
> After talking to someone you basically have three wires going to sensor
> 5V source input (black), Gnd, and 5V output to Speedometer / Odometer
> gauge. If there is not 5V input then it is probably the wiring or
> gauge, if there is 5V in , probably sensor, but If it is not the
> sensor, I'm not sure how to access cluster connector]
>
> Second, no one here is a mind reader or knows you so we have no clue
> what you are driving. (let alone lots of us do own more than one type
> of Jeep)
> [ YJ, 1992 Wrangler 4.0L ]
>
> And third if it is a YJ you are talking about, why don't you just pull
> the codes and see what the computer 'thinks' is wrong?
> [ No experience with reading code... I't sounds like a great
> troubleshooting tool, do you need a reading device and where do you
> access the port for connection ? Where do I buy one or do I have to
> take it to a shop?]
> Thanks
03-28-2005 | 11:20 AM
#13
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Well, stalling in neutral is because you have the speed sensor
disconnected.
If you reconnect it and it stops stalling, the sensor is likely working.
The sensor generates it's own pulses. Just spin it by hand with a meter
on it. 8 pulses per revolution off pin 1 and 2 likely.
'What' is the speedometer doing or not doing anyway?
To pull the codes, you need to hook everything back up and drive it for
a bit.
Then stop, rev it ti 2500 and let it down to idle and cycle everything
like the AC and if an automatic all the gears.
Then shut it down and turn the key on, off, on, off, on and count the
flashes on the dash light. It will flash a sequence, then pause, then
flash again. The final flash will be a 5 and a 5 or code 55 that means
no more codes.
If you get a code 15, the speed sensor or it's circuit is bad.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
updawaz00@hotmail.com wrote:
>
> First off what are you trying to fix?
>
> [ Speedometer in this instance... but also stalling problem in neutral
> After talking to someone you basically have three wires going to sensor
> 5V source input (black), Gnd, and 5V output to Speedometer / Odometer
> gauge. If there is not 5V input then it is probably the wiring or
> gauge, if there is 5V in , probably sensor, but If it is not the
> sensor, I'm not sure how to access cluster connector]
>
> Second, no one here is a mind reader or knows you so we have no clue
> what you are driving. (let alone lots of us do own more than one type
> of Jeep)
> [ YJ, 1992 Wrangler 4.0L ]
>
> And third if it is a YJ you are talking about, why don't you just pull
> the codes and see what the computer 'thinks' is wrong?
> [ No experience with reading code... I't sounds like a great
> troubleshooting tool, do you need a reading device and where do you
> access the port for connection ? Where do I buy one or do I have to
> take it to a shop?]
> Thanks
disconnected.
If you reconnect it and it stops stalling, the sensor is likely working.
The sensor generates it's own pulses. Just spin it by hand with a meter
on it. 8 pulses per revolution off pin 1 and 2 likely.
'What' is the speedometer doing or not doing anyway?
To pull the codes, you need to hook everything back up and drive it for
a bit.
Then stop, rev it ti 2500 and let it down to idle and cycle everything
like the AC and if an automatic all the gears.
Then shut it down and turn the key on, off, on, off, on and count the
flashes on the dash light. It will flash a sequence, then pause, then
flash again. The final flash will be a 5 and a 5 or code 55 that means
no more codes.
If you get a code 15, the speed sensor or it's circuit is bad.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
updawaz00@hotmail.com wrote:
>
> First off what are you trying to fix?
>
> [ Speedometer in this instance... but also stalling problem in neutral
> After talking to someone you basically have three wires going to sensor
> 5V source input (black), Gnd, and 5V output to Speedometer / Odometer
> gauge. If there is not 5V input then it is probably the wiring or
> gauge, if there is 5V in , probably sensor, but If it is not the
> sensor, I'm not sure how to access cluster connector]
>
> Second, no one here is a mind reader or knows you so we have no clue
> what you are driving. (let alone lots of us do own more than one type
> of Jeep)
> [ YJ, 1992 Wrangler 4.0L ]
>
> And third if it is a YJ you are talking about, why don't you just pull
> the codes and see what the computer 'thinks' is wrong?
> [ No experience with reading code... I't sounds like a great
> troubleshooting tool, do you need a reading device and where do you
> access the port for connection ? Where do I buy one or do I have to
> take it to a shop?]
> Thanks
03-28-2005 | 12:40 PM
#14
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Mike Romain wrote:
> Well, stalling in neutral is because you have the speed sensor
> disconnected.
{ OR THE SENSOR IS NOT WORKING CONNECTED}
> The sensor generates it's own pulses. Just spin it by hand with a
meter
> on it. 8 pulses per revolution off pin 1 and 2 likely.
{GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
VOLT SOURCE FED BY THE CONNECTOR CABLE}
> 'What' is the speedometer doing or not doing anyway?
>
> To pull the codes, you need to hook everything back up and drive it
for
> a bit.
>
> Then stop, rev it ti 2500 and let it down to idle and cycle
everything
> like the AC and if an automatic all the gears.
>
> Then shut it down and turn the key on, off, on, off, on and count the
> flashes on the dash light. It will flash a sequence, then pause,
then
> flash again. The final flash will be a 5 and a 5 or code 55 that
means
> no more codes.
>
> If you get a code 15, the speed sensor or it's circuit is bad.
SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
CABLE.
YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> updawaz00@hotmail.com wrote:
> >
> > First off what are you trying to fix?
> >
> > [ Speedometer in this instance... but also stalling problem in
neutral
> > After talking to someone you basically have three wires going to
sensor
> > 5V source input (black), Gnd, and 5V output to Speedometer /
Odometer
> > gauge. If there is not 5V input then it is probably the wiring or
> > gauge, if there is 5V in , probably sensor, but If it is not the
> > sensor, I'm not sure how to access cluster connector]
> >
> > Second, no one here is a mind reader or knows you so we have no
clue
> > what you are driving. (let alone lots of us do own more than one
type
> > of Jeep)
> > [ YJ, 1992 Wrangler 4.0L ]
> >
> > And third if it is a YJ you are talking about, why don't you just
pull
> > the codes and see what the computer 'thinks' is wrong?
> > [ No experience with reading code... I't sounds like a great
> > troubleshooting tool, do you need a reading device and where do you
> > access the port for connection ? Where do I buy one or do I have to
> > take it to a shop?]
> > Thanks
03-28-2005 | 12:40 PM
#15
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Mike Romain wrote:
> Well, stalling in neutral is because you have the speed sensor
> disconnected.
{ OR THE SENSOR IS NOT WORKING CONNECTED}
> The sensor generates it's own pulses. Just spin it by hand with a
meter
> on it. 8 pulses per revolution off pin 1 and 2 likely.
{GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
VOLT SOURCE FED BY THE CONNECTOR CABLE}
> 'What' is the speedometer doing or not doing anyway?
>
> To pull the codes, you need to hook everything back up and drive it
for
> a bit.
>
> Then stop, rev it ti 2500 and let it down to idle and cycle
everything
> like the AC and if an automatic all the gears.
>
> Then shut it down and turn the key on, off, on, off, on and count the
> flashes on the dash light. It will flash a sequence, then pause,
then
> flash again. The final flash will be a 5 and a 5 or code 55 that
means
> no more codes.
>
> If you get a code 15, the speed sensor or it's circuit is bad.
SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
CABLE.
YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> updawaz00@hotmail.com wrote:
> >
> > First off what are you trying to fix?
> >
> > [ Speedometer in this instance... but also stalling problem in
neutral
> > After talking to someone you basically have three wires going to
sensor
> > 5V source input (black), Gnd, and 5V output to Speedometer /
Odometer
> > gauge. If there is not 5V input then it is probably the wiring or
> > gauge, if there is 5V in , probably sensor, but If it is not the
> > sensor, I'm not sure how to access cluster connector]
> >
> > Second, no one here is a mind reader or knows you so we have no
clue
> > what you are driving. (let alone lots of us do own more than one
type
> > of Jeep)
> > [ YJ, 1992 Wrangler 4.0L ]
> >
> > And third if it is a YJ you are talking about, why don't you just
pull
> > the codes and see what the computer 'thinks' is wrong?
> > [ No experience with reading code... I't sounds like a great
> > troubleshooting tool, do you need a reading device and where do you
> > access the port for connection ? Where do I buy one or do I have to
> > take it to a shop?]
> > Thanks
03-28-2005 | 12:40 PM
#16
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Mike Romain wrote:
> Well, stalling in neutral is because you have the speed sensor
> disconnected.
{ OR THE SENSOR IS NOT WORKING CONNECTED}
> The sensor generates it's own pulses. Just spin it by hand with a
meter
> on it. 8 pulses per revolution off pin 1 and 2 likely.
{GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
VOLT SOURCE FED BY THE CONNECTOR CABLE}
> 'What' is the speedometer doing or not doing anyway?
>
> To pull the codes, you need to hook everything back up and drive it
for
> a bit.
>
> Then stop, rev it ti 2500 and let it down to idle and cycle
everything
> like the AC and if an automatic all the gears.
>
> Then shut it down and turn the key on, off, on, off, on and count the
> flashes on the dash light. It will flash a sequence, then pause,
then
> flash again. The final flash will be a 5 and a 5 or code 55 that
means
> no more codes.
>
> If you get a code 15, the speed sensor or it's circuit is bad.
SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
CABLE.
YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> updawaz00@hotmail.com wrote:
> >
> > First off what are you trying to fix?
> >
> > [ Speedometer in this instance... but also stalling problem in
neutral
> > After talking to someone you basically have three wires going to
sensor
> > 5V source input (black), Gnd, and 5V output to Speedometer /
Odometer
> > gauge. If there is not 5V input then it is probably the wiring or
> > gauge, if there is 5V in , probably sensor, but If it is not the
> > sensor, I'm not sure how to access cluster connector]
> >
> > Second, no one here is a mind reader or knows you so we have no
clue
> > what you are driving. (let alone lots of us do own more than one
type
> > of Jeep)
> > [ YJ, 1992 Wrangler 4.0L ]
> >
> > And third if it is a YJ you are talking about, why don't you just
pull
> > the codes and see what the computer 'thinks' is wrong?
> > [ No experience with reading code... I't sounds like a great
> > troubleshooting tool, do you need a reading device and where do you
> > access the port for connection ? Where do I buy one or do I have to
> > take it to a shop?]
> > Thanks
03-28-2005 | 02:16 PM
#17
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Right, now I remember that hall sensor has to be plugged in to test it
just switches the power to pulses. A hand turn should give the pulses
though, same as a distributor one.
If the ground tag is bad, that is likely a stud on the rear passenger
side of the block with a bunch of small black wires on it. The YJ has
one more ground tag on the e-brake frame, but that one usually kills the
fuel pump.
Mike
josh00@comcast.net wrote:
>
> Mike Romain wrote:
> > Well, stalling in neutral is because you have the speed sensor
> > disconnected.
>
> { OR THE SENSOR IS NOT WORKING CONNECTED}
> > The sensor generates it's own pulses. Just spin it by hand with a
> meter
> > on it. 8 pulses per revolution off pin 1 and 2 likely.
>
> {GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
> VOLT SOURCE FED BY THE CONNECTOR CABLE}
>
> > 'What' is the speedometer doing or not doing anyway?
> >
> > To pull the codes, you need to hook everything back up and drive it
> for
> > a bit.
> >
> > Then stop, rev it ti 2500 and let it down to idle and cycle
> everything
> > like the AC and if an automatic all the gears.
> >
> > Then shut it down and turn the key on, off, on, off, on and count the
> > flashes on the dash light. It will flash a sequence, then pause,
> then
> > flash again. The final flash will be a 5 and a 5 or code 55 that
> means
> > no more codes.
> >
> > If you get a code 15, the speed sensor or it's circuit is bad.
>
> SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
> SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
> CABLE.
> YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
> NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > updawaz00@hotmail.com wrote:
> > >
> > > First off what are you trying to fix?
> > >
> > > [ Speedometer in this instance... but also stalling problem in
> neutral
> > > After talking to someone you basically have three wires going to
> sensor
> > > 5V source input (black), Gnd, and 5V output to Speedometer /
> Odometer
> > > gauge. If there is not 5V input then it is probably the wiring or
> > > gauge, if there is 5V in , probably sensor, but If it is not the
> > > sensor, I'm not sure how to access cluster connector]
> > >
> > > Second, no one here is a mind reader or knows you so we have no
> clue
> > > what you are driving. (let alone lots of us do own more than one
> type
> > > of Jeep)
> > > [ YJ, 1992 Wrangler 4.0L ]
> > >
> > > And third if it is a YJ you are talking about, why don't you just
> pull
> > > the codes and see what the computer 'thinks' is wrong?
> > > [ No experience with reading code... I't sounds like a great
> > > troubleshooting tool, do you need a reading device and where do you
> > > access the port for connection ? Where do I buy one or do I have to
> > > take it to a shop?]
> > > Thanks
just switches the power to pulses. A hand turn should give the pulses
though, same as a distributor one.
If the ground tag is bad, that is likely a stud on the rear passenger
side of the block with a bunch of small black wires on it. The YJ has
one more ground tag on the e-brake frame, but that one usually kills the
fuel pump.
Mike
josh00@comcast.net wrote:
>
> Mike Romain wrote:
> > Well, stalling in neutral is because you have the speed sensor
> > disconnected.
>
> { OR THE SENSOR IS NOT WORKING CONNECTED}
> > The sensor generates it's own pulses. Just spin it by hand with a
> meter
> > on it. 8 pulses per revolution off pin 1 and 2 likely.
>
> {GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
> VOLT SOURCE FED BY THE CONNECTOR CABLE}
>
> > 'What' is the speedometer doing or not doing anyway?
> >
> > To pull the codes, you need to hook everything back up and drive it
> for
> > a bit.
> >
> > Then stop, rev it ti 2500 and let it down to idle and cycle
> everything
> > like the AC and if an automatic all the gears.
> >
> > Then shut it down and turn the key on, off, on, off, on and count the
> > flashes on the dash light. It will flash a sequence, then pause,
> then
> > flash again. The final flash will be a 5 and a 5 or code 55 that
> means
> > no more codes.
> >
> > If you get a code 15, the speed sensor or it's circuit is bad.
>
> SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
> SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
> CABLE.
> YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
> NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > updawaz00@hotmail.com wrote:
> > >
> > > First off what are you trying to fix?
> > >
> > > [ Speedometer in this instance... but also stalling problem in
> neutral
> > > After talking to someone you basically have three wires going to
> sensor
> > > 5V source input (black), Gnd, and 5V output to Speedometer /
> Odometer
> > > gauge. If there is not 5V input then it is probably the wiring or
> > > gauge, if there is 5V in , probably sensor, but If it is not the
> > > sensor, I'm not sure how to access cluster connector]
> > >
> > > Second, no one here is a mind reader or knows you so we have no
> clue
> > > what you are driving. (let alone lots of us do own more than one
> type
> > > of Jeep)
> > > [ YJ, 1992 Wrangler 4.0L ]
> > >
> > > And third if it is a YJ you are talking about, why don't you just
> pull
> > > the codes and see what the computer 'thinks' is wrong?
> > > [ No experience with reading code... I't sounds like a great
> > > troubleshooting tool, do you need a reading device and where do you
> > > access the port for connection ? Where do I buy one or do I have to
> > > take it to a shop?]
> > > Thanks
03-28-2005 | 02:16 PM
#18
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Right, now I remember that hall sensor has to be plugged in to test it
just switches the power to pulses. A hand turn should give the pulses
though, same as a distributor one.
If the ground tag is bad, that is likely a stud on the rear passenger
side of the block with a bunch of small black wires on it. The YJ has
one more ground tag on the e-brake frame, but that one usually kills the
fuel pump.
Mike
josh00@comcast.net wrote:
>
> Mike Romain wrote:
> > Well, stalling in neutral is because you have the speed sensor
> > disconnected.
>
> { OR THE SENSOR IS NOT WORKING CONNECTED}
> > The sensor generates it's own pulses. Just spin it by hand with a
> meter
> > on it. 8 pulses per revolution off pin 1 and 2 likely.
>
> {GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
> VOLT SOURCE FED BY THE CONNECTOR CABLE}
>
> > 'What' is the speedometer doing or not doing anyway?
> >
> > To pull the codes, you need to hook everything back up and drive it
> for
> > a bit.
> >
> > Then stop, rev it ti 2500 and let it down to idle and cycle
> everything
> > like the AC and if an automatic all the gears.
> >
> > Then shut it down and turn the key on, off, on, off, on and count the
> > flashes on the dash light. It will flash a sequence, then pause,
> then
> > flash again. The final flash will be a 5 and a 5 or code 55 that
> means
> > no more codes.
> >
> > If you get a code 15, the speed sensor or it's circuit is bad.
>
> SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
> SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
> CABLE.
> YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
> NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > updawaz00@hotmail.com wrote:
> > >
> > > First off what are you trying to fix?
> > >
> > > [ Speedometer in this instance... but also stalling problem in
> neutral
> > > After talking to someone you basically have three wires going to
> sensor
> > > 5V source input (black), Gnd, and 5V output to Speedometer /
> Odometer
> > > gauge. If there is not 5V input then it is probably the wiring or
> > > gauge, if there is 5V in , probably sensor, but If it is not the
> > > sensor, I'm not sure how to access cluster connector]
> > >
> > > Second, no one here is a mind reader or knows you so we have no
> clue
> > > what you are driving. (let alone lots of us do own more than one
> type
> > > of Jeep)
> > > [ YJ, 1992 Wrangler 4.0L ]
> > >
> > > And third if it is a YJ you are talking about, why don't you just
> pull
> > > the codes and see what the computer 'thinks' is wrong?
> > > [ No experience with reading code... I't sounds like a great
> > > troubleshooting tool, do you need a reading device and where do you
> > > access the port for connection ? Where do I buy one or do I have to
> > > take it to a shop?]
> > > Thanks
just switches the power to pulses. A hand turn should give the pulses
though, same as a distributor one.
If the ground tag is bad, that is likely a stud on the rear passenger
side of the block with a bunch of small black wires on it. The YJ has
one more ground tag on the e-brake frame, but that one usually kills the
fuel pump.
Mike
josh00@comcast.net wrote:
>
> Mike Romain wrote:
> > Well, stalling in neutral is because you have the speed sensor
> > disconnected.
>
> { OR THE SENSOR IS NOT WORKING CONNECTED}
> > The sensor generates it's own pulses. Just spin it by hand with a
> meter
> > on it. 8 pulses per revolution off pin 1 and 2 likely.
>
> {GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
> VOLT SOURCE FED BY THE CONNECTOR CABLE}
>
> > 'What' is the speedometer doing or not doing anyway?
> >
> > To pull the codes, you need to hook everything back up and drive it
> for
> > a bit.
> >
> > Then stop, rev it ti 2500 and let it down to idle and cycle
> everything
> > like the AC and if an automatic all the gears.
> >
> > Then shut it down and turn the key on, off, on, off, on and count the
> > flashes on the dash light. It will flash a sequence, then pause,
> then
> > flash again. The final flash will be a 5 and a 5 or code 55 that
> means
> > no more codes.
> >
> > If you get a code 15, the speed sensor or it's circuit is bad.
>
> SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
> SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
> CABLE.
> YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
> NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > updawaz00@hotmail.com wrote:
> > >
> > > First off what are you trying to fix?
> > >
> > > [ Speedometer in this instance... but also stalling problem in
> neutral
> > > After talking to someone you basically have three wires going to
> sensor
> > > 5V source input (black), Gnd, and 5V output to Speedometer /
> Odometer
> > > gauge. If there is not 5V input then it is probably the wiring or
> > > gauge, if there is 5V in , probably sensor, but If it is not the
> > > sensor, I'm not sure how to access cluster connector]
> > >
> > > Second, no one here is a mind reader or knows you so we have no
> clue
> > > what you are driving. (let alone lots of us do own more than one
> type
> > > of Jeep)
> > > [ YJ, 1992 Wrangler 4.0L ]
> > >
> > > And third if it is a YJ you are talking about, why don't you just
> pull
> > > the codes and see what the computer 'thinks' is wrong?
> > > [ No experience with reading code... I't sounds like a great
> > > troubleshooting tool, do you need a reading device and where do you
> > > access the port for connection ? Where do I buy one or do I have to
> > > take it to a shop?]
> > > Thanks
03-28-2005 | 02:16 PM
#19
Guest
Posts: n/a
Re: access instrument cluster connector & speedo sensor troubleshooting
Right, now I remember that hall sensor has to be plugged in to test it
just switches the power to pulses. A hand turn should give the pulses
though, same as a distributor one.
If the ground tag is bad, that is likely a stud on the rear passenger
side of the block with a bunch of small black wires on it. The YJ has
one more ground tag on the e-brake frame, but that one usually kills the
fuel pump.
Mike
josh00@comcast.net wrote:
>
> Mike Romain wrote:
> > Well, stalling in neutral is because you have the speed sensor
> > disconnected.
>
> { OR THE SENSOR IS NOT WORKING CONNECTED}
> > The sensor generates it's own pulses. Just spin it by hand with a
> meter
> > on it. 8 pulses per revolution off pin 1 and 2 likely.
>
> {GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
> VOLT SOURCE FED BY THE CONNECTOR CABLE}
>
> > 'What' is the speedometer doing or not doing anyway?
> >
> > To pull the codes, you need to hook everything back up and drive it
> for
> > a bit.
> >
> > Then stop, rev it ti 2500 and let it down to idle and cycle
> everything
> > like the AC and if an automatic all the gears.
> >
> > Then shut it down and turn the key on, off, on, off, on and count the
> > flashes on the dash light. It will flash a sequence, then pause,
> then
> > flash again. The final flash will be a 5 and a 5 or code 55 that
> means
> > no more codes.
> >
> > If you get a code 15, the speed sensor or it's circuit is bad.
>
> SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
> SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
> CABLE.
> YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
> NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > updawaz00@hotmail.com wrote:
> > >
> > > First off what are you trying to fix?
> > >
> > > [ Speedometer in this instance... but also stalling problem in
> neutral
> > > After talking to someone you basically have three wires going to
> sensor
> > > 5V source input (black), Gnd, and 5V output to Speedometer /
> Odometer
> > > gauge. If there is not 5V input then it is probably the wiring or
> > > gauge, if there is 5V in , probably sensor, but If it is not the
> > > sensor, I'm not sure how to access cluster connector]
> > >
> > > Second, no one here is a mind reader or knows you so we have no
> clue
> > > what you are driving. (let alone lots of us do own more than one
> type
> > > of Jeep)
> > > [ YJ, 1992 Wrangler 4.0L ]
> > >
> > > And third if it is a YJ you are talking about, why don't you just
> pull
> > > the codes and see what the computer 'thinks' is wrong?
> > > [ No experience with reading code... I't sounds like a great
> > > troubleshooting tool, do you need a reading device and where do you
> > > access the port for connection ? Where do I buy one or do I have to
> > > take it to a shop?]
> > > Thanks
just switches the power to pulses. A hand turn should give the pulses
though, same as a distributor one.
If the ground tag is bad, that is likely a stud on the rear passenger
side of the block with a bunch of small black wires on it. The YJ has
one more ground tag on the e-brake frame, but that one usually kills the
fuel pump.
Mike
josh00@comcast.net wrote:
>
> Mike Romain wrote:
> > Well, stalling in neutral is because you have the speed sensor
> > disconnected.
>
> { OR THE SENSOR IS NOT WORKING CONNECTED}
> > The sensor generates it's own pulses. Just spin it by hand with a
> meter
> > on it. 8 pulses per revolution off pin 1 and 2 likely.
>
> {GENERATES A MAGNETIC FIELD TO PRODUCE PULSES, BUT IT STILL NEEDS A 5
> VOLT SOURCE FED BY THE CONNECTOR CABLE}
>
> > 'What' is the speedometer doing or not doing anyway?
> >
> > To pull the codes, you need to hook everything back up and drive it
> for
> > a bit.
> >
> > Then stop, rev it ti 2500 and let it down to idle and cycle
> everything
> > like the AC and if an automatic all the gears.
> >
> > Then shut it down and turn the key on, off, on, off, on and count the
> > flashes on the dash light. It will flash a sequence, then pause,
> then
> > flash again. The final flash will be a 5 and a 5 or code 55 that
> means
> > no more codes.
> >
> > If you get a code 15, the speed sensor or it's circuit is bad.
>
> SAME DEAL BY DOING MANUALLY WITH A METER. TO BACK UP WHAT THE OBS IS
> SHOWING, GO AHEAD AND CHECK TO SEE IF 5 VOLTS ARE PRESENT FROM THE
> CABLE.
> YES: SENSOR BAD OR GROUND WIRE NOT CONNECTED.
> NO: 5V SHORTED OR BAD CONNECTION AT THE MULTICONNECTOR.
>
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > updawaz00@hotmail.com wrote:
> > >
> > > First off what are you trying to fix?
> > >
> > > [ Speedometer in this instance... but also stalling problem in
> neutral
> > > After talking to someone you basically have three wires going to
> sensor
> > > 5V source input (black), Gnd, and 5V output to Speedometer /
> Odometer
> > > gauge. If there is not 5V input then it is probably the wiring or
> > > gauge, if there is 5V in , probably sensor, but If it is not the
> > > sensor, I'm not sure how to access cluster connector]
> > >
> > > Second, no one here is a mind reader or knows you so we have no
> clue
> > > what you are driving. (let alone lots of us do own more than one
> type
> > > of Jeep)
> > > [ YJ, 1992 Wrangler 4.0L ]
> > >
> > > And third if it is a YJ you are talking about, why don't you just
> pull
> > > the codes and see what the computer 'thinks' is wrong?
> > > [ No experience with reading code... I't sounds like a great
> > > troubleshooting tool, do you need a reading device and where do you
> > > access the port for connection ? Where do I buy one or do I have to
> > > take it to a shop?]
> > > Thanks
Thread
Thread Starter
Forum
Replies
Last Post
jeep videos
Jeep Videos - Pictures
0
04-01-2008 02:15 AM
jeep videos
Jeep Videos - Pictures
0
03-31-2008 03:23 AM
randallbrink@adelphia.net
Jeep Mailing List
0
12-26-2005 01:22 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)